Skip to content

A free roof inspection and a photo report of the details: (919) 980-9943

(919) 980-9943

ServicesGutters

Gutter Installation and Replacement in Pittsboro

We install continuous aluminum gutters sloped to drain, anchored into solid wood and paired with downspouts that can keep up with a summer downpour. Water leaves your roof and stays away from your foundation, and you see a photo report of what we found before any work starts.

Worker on an aluminum extension ladder drilling to fasten a white seamless gutter along the eave of a brick ranch house, with a white downspout at the corner

Gutters that actually carry the water away

A gutter only has one job, and it usually fails because of small shortcuts at install: not enough slope, hangers set too far apart, a joint right over the front door, or a downspout that empties beside the foundation. We spend our time on those details, since they are what separate a gutter that drains well for years from one that droops after a couple of winters.

We handle full gutter replacement, new runs on homes that never had them, and downspout fixes when the gutters are sound but the water lands in the wrong place. As a roofing company, we also check the roof edge where the gutter attaches. If the drip edge is missing or the shingles hang wrong, a new gutter alone will not stop the leak, and we will say so before you spend anything.

What a gutter job with us includes

Seamless runs cut to your roof
A machine in our truck shapes each gutter from a coil of aluminum, sized to the full length of the eave. The only joints left are at the corners, which means far fewer places for leaks and streaks to start.
Hidden hangers set into framing
Every hanger goes through the fascia and into the rafter tail or solid blocking behind it. We space them much closer than old spike-and-ferrule systems, so a run stays straight even when it fills with wet leaves.
Measured slope toward each outlet
A chalk line guides a gentle fall toward each downspout, enough to drain without looking tilted from the yard. On long eaves we pitch from the middle so water heads to both ends.
Downspouts sized for the roof
Big or steep roof sections shed water in a hurry. When it makes sense, we go with larger downspouts and add outlets so the gutter empties faster than it fills.
Extensions that clear the foundation
Each downspout finishes with an elbow and extension or a splash block that sends water several feet out, past your crawlspace and garden beds.
Sealed corners and end caps
We rivet miters and end caps, seal them from the inside, and run a hose through the system before we leave.

Signs your gutters need attention

  • Water spilling over the front edge

    When rain pours over the lip in an ordinary storm, the gutter is clogged, too small or sloped the wrong way. Each cause has its own fix.

  • Sagging or pulling away

    A run that droops between hangers or tilts away from the house typically has loose fasteners or soft fascia behind it.

  • Stains, peeling or rot behind the gutter

    Dark streaks on the fascia or spongy wood at the roof edge mean water is slipping behind the gutter. The cause is often a missing drip edge rather than the gutter itself.

  • Washed-out soil or a damp crawlspace

    Ruts under the eaves or puddles by the foundation point to downspouts ending too close to the house. In red clay soil, that water tends to sit right where you do not want it.

  • Leaking seams and corners

    Drips at the joints during rain mean the sealant has given out. Older sectional gutters show this first.

What affects the price of new gutters

A gutter price mostly reflects two things: how many feet of roof edge your home has and how hard that edge is to work on. Once we finish the inspection, you get the number in writing, and it stays the same on install day. Financing is available through Acorn Finance for anyone who would rather spread the cost out.

Footage and corners

More roof edge means more gutter. Every inside and outside corner is a miter we cut, rivet and seal by hand, so a house with lots of corners takes longer.

Gutter width and metal gauge

Wider profiles and heavier aluminum cost more up front. In return they handle the runoff from large roof planes and resist dents from ladders and dropped limbs.

Downspout count and size

Extra outlets, larger downspouts and longer extensions add material and labor. They are also usually what keeps water out of your crawlspace.

Height and access

Second-story eaves, steep pitches and tight spots beside decks or planting beds call for more setup before the first hanger goes in.

Fascia condition

If the board behind the old gutter is rotted, it gets replaced first. New hangers need sound wood to bite into.

How the day goes

  1. 1

    Inspection and photo report

    We look over your gutters, downspouts, fascia and roof edge, then send you photos of what we saw. You will know whether it calls for a repair, a partial replacement or a full set before price comes up.

  2. 2

    Written estimate

    The estimate spells out footage, downspouts, any fascia work and your color choice. When a storm caused the damage, we can join the adjuster's visit and help you with the claim from start to finish.

  3. 3

    Removal and prep

    We take the old gutters down, probe the fascia for soft wood and show you anything we find before it gets covered. Our ladders use stabilizers so they never lean on the new gutter line.

  4. 4

    Install and water test

    We form the runs, set the slope, hang and seal each section, then send water down every run to make sure it reaches the outlet.

  5. 5

    Cleanup and walkthrough

    We haul away the old metal, sweep up stray screws and rivets, and walk around the house with you to show where each downspout drains.

Roofer in a safety harness on an aluminum ladder photographing worn asphalt shingles, a box vent and a pipe vent boot on a brick home's roof

Gutter questions we hear often

Can you just fix my gutters instead of replacing them?

Often, yes. Resealing a leaky corner, rehanging a drooping section or moving a downspout costs far less than a full set. We recommend replacement when sectional gutters leak at many joints, are badly dented, or run downhill the wrong way along their whole length.

How long does a gutter replacement take?

Most homes are done in a single day. Fascia repairs or a large two-story house can stretch that a bit, and your estimate will include the schedule we expect.

What size gutters does my house need?

We look at the square footage of roof feeding each gutter and at the pitch, since a steeper slope sends water down faster. Standard gutters work on plenty of houses. Steep roofs, or valleys that pour into a single corner, usually need a wider profile or extra downspouts, and your photo report will show our measurements and reasoning.

Why does water still get behind my gutters?

Usually the shingles or drip edge are not directing water into the gutter, so it runs down the fascia instead. Since we are roofers, we check that edge during every inspection. If it needs attention, we can take care of the roof repair while we are already on the ladder.

Will storm damage to my gutters be covered by insurance?

Gutters dented by hail or torn down by falling limbs are often included on the same claim as the roof. We photograph the damage, can meet the adjuster at your home, and help you through the claim process step by step. Whether it is covered is up to your insurer, and our storm damage repair page explains more.

Brick ranch house with dark brown architectural shingle roof, ladder at the porch eave, and shingle bundles on a blue tarp in the front yard on an overcast day

See your gutters the way we see them

We will look over your gutters, downspouts and roof edge for free, then send photos of each spot that matters. You decide what happens next, and there is no pressure to book anything.